Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Before
After
Before
After
Before
AfterAbatement Technologies Air Duct Cleaning in Leander: What to Know First
We provide independent Abatement Technologies air duct cleaning in Leander with written pricing before any work begins, typically completing residential jobs in a single scheduled visit. Most Leander homeowners with Abatement Technologies systems pay between $380 and $720 for a full supply-and-return cleaning, depending on home size and what the inspection camera actually shows inside the ductwork. Every job ends with a documented photo record of every duct run, delivered as part of the standard job record.
This page is for Abatement Technologies owners in Leander who want to understand how their specific equipment behaves in local conditions before deciding who to hire. If you own an Abatement Technologies HEPA-AIRE or Predator series unit, or you’ve noticed your Abatement Technologies-powered ventilation system pushing less air than it used to, call us at (737) 252-1285. We’ll put a camera in your ducts first, then talk about what comes next.
How Abatement Technologies Products Fail - and How We Fix Them
- HEPA-AIRE H5000 series: blower motor bearing wear from cedar pollen loading. Leander’s cedar season runs heavy from December through February, and the H5000’s high-static blower works harder than spec when filters load past their pressure drop rating. We see bearing noise and reduced CFM in Crystal Falls and Travisso homes every January. Our fix: full duct pull-cleaning to drop static pressure, then motor amp-draw testing against Abatement Technologies factory spec. If the motor’s drawing 15% over nameplate, we document it and quote replacement before the bearing seizes.
- Predator 1200 portable units: flexible duct collar fatigue at the plenum connection. The Predator’s 12-inch flexible collar hardens in Leander’s attic heat, then cracks where it meets the galvanized plenum box. We’ve found this on six jobs in the past year, all in homes built 2018-2021. Our fix: remove the damaged collar, inspect the plenum interior for debris fallout from the gap, and replace with a reinforced silicone transition rated for 180°F - not the standard vinyl that fails again in two summers.
- ABATEMENT CAT5 negative air machines: HEPA filter bypass from improper seal seating. The CAT5’s filter bank uses a knife-edge seal that leaks if the cam latches aren’t torqued evenly. In Leander’s new construction, we’ve found this causes visible dust bypass on the clean side during post-buildout cleaning. Our fix: filter bank teardown, seal inspection with light test, and reassembly with torque verification - documented in the photo record.
- HEPA-AIRE H2000: condensate pan overflow into return ductwork. The H2000’s compact drain pan overflows when algae builds up in Leander’s hard water conditions, sending moisture into the return boot. We’ve pulled 2-inch algae mats from returns in Cedar Park-adjacent Leander homes. Our fix: pan cleaning and biocide treatment, then duct drying with negative-pressure extraction and pan-level sensor check.
- Portable HEPA systems: power cord strain relief failure from frequent relocation. Abatement Technologies’ portable units get moved between jobs by restoration crews, and the cord grip loosens until conductors fatigue. We see this on units that owners bought used or inherited from previous contractors. Our fix: cord replacement with hospital-grade strain relief, then full ground-fault and amp-draw testing before the unit goes back into your ductwork.
Our Abatement Technologies Air Duct Cleaning Process
- 1
Inspection with video documentation. We feed a camera through every accessible duct run and show you the feed in real time. If we don’t find debris buildup or damage, we don’t invent work. Haven Standard Clause 1: written price before any work starts.
- 2
Static pressure and airflow testing. We measure pre-cleaning static across the Abatement Technologies unit and compare to manufacturer spec. This tells us whether the problem is duct restriction or equipment performance.
- 3
Negative-pressure extraction with Rotobrush or Abatement Technologies-compatible agitation. We select the brush head and vacuum cfm based on your duct material - flex duct gets softer agitation, galvanized gets stiffer bristles. The equipment roster includes Abatement Technologies, Rotobrush, and Nikro units we can match to the job.
- 4
Component-specific cleaning. For Abatement Technologies HEPA-AIRE systems, we pull and clean the blower wheel, inspect the filter seal track, and verify damper operation. For Predator portables, we clean the filter bank and check collar integrity.
- 5
Post-cleaning verification. We re-run static pressure and airflow, then camera every run again. The before-and-after photo record goes to you as a standard deliverable, not an upsell.
- 6
Written scope delivery with 365-Day Done Right Promise. You get the photo record, the test results, and the warranty document before we pack up. If something’s not right, we make it right - backed in writing, not subject to manager approval.
BeforeAfterWhat Abatement Technologies Air Duct Cleaning Costs in Leander
These are real ranges for Abatement Technologies systems we’ve cleaned in Leander, based on 52,000+ jobs since 2013:
| Service | Typical Range | What Moves the Price |
|---|---|---|
| Single-system residential cleaning (supply + return) | $380 - $550 | Home size, duct accessibility, debris type |
| Abatement Technologies HEPA-AIRE with blower service | $480 - $720 | Blower removal, bearing check, filter bank depth |
| Post-construction/new home initial cleaning | $520 - $780 | Construction debris volume, register count, flex duct damage |
| Predator portable unit restoration cleaning | $340 - $490 | Filter replacement, collar repair, electrical safety check |
| Video inspection only (no cleaning needed) | $0 - $125 | Free if we perform cleaning; flat rate if system is clean |
Price drivers specific to Leander: cedar pollen loading adds time in winter months; new construction in Crystal Falls and Travisso often has drywall dust compaction; older homes near Bagdad Road may have original galvanized duct with rust scale. We quote one flat price per system, agreed in writing before work starts. No per-vent pricing. No $79 coupon that becomes $600 on the invoice. Call (737) 252-1285 for a free estimate - we’ll show you what the camera sees before you decide.
Why Leander Homeowners Call CleanRun Air Duct Cleaning Leander for Abatement Technologies Work
We’re an independent Abatement Technologies service provider - not affiliated with or authorized by the manufacturer - which means we work on what your system actually needs, not what a brand protocol prescribes. Tomas Reyes, our owner, spent years running crews through Leander’s neighborhoods and knows the difference between cedar pollen buildup and construction debris by sight. Our technicians are background-checked and uniformed under Haven Standard Clause 3: Verified Crews. We also service Lennox, Trane, and Carrier systems, so if your Abatement Technologies unit is part of a mixed-manufacturer setup, we don’t need to call in a second contractor. The 365-Day Done Right Promise applies to every job, and the photo record is included, not extra. You can verify our equipment - Rotobrush, Nikro, Abatement Technologies, Honeywell, Aprilaire, Guardsman - before we start.
FAQs
No. Routine maintenance and professional cleaning do not void Abatement Technologies equipment warranties, provided the work doesn’t damage components. We document our process with photos to prove proper handling if a future warranty claim arises. If you’re concerned about a specific warranty term, bring your documentation and we’ll review it before quoting - call (737) 252-1285.
OEM filters match the original pressure-drop and efficiency specs, but quality aftermarket filters from Honeywell or Aprilaire often perform equivalently at lower cost. We stock both and will show you the MERV rating and pressure-drop data for each option before you choose. Haven Standard Clause 1: written price for either path before work starts.
Our documented photo record shows the inside of every duct run before and after cleaning, with timestamps. You receive this as a standard deliverable, not an add-on. If a run doesn’t show visible improvement, we re-clean it at no charge under the 365-Day Done Right Promise.
Noise usually indicates mechanical wear, not dirty ducts. We start with a camera inspection and amp-draw test to separate duct restriction from blower or bearing failure. If cleaning won’t solve it, we’ll tell you before quoting anything. Free second opinions on any written estimate from another contractor.
Every 3 to 5 years for most Leander homes, sooner if you have pets, recent construction, or heavy cedar pollen exposure. In Crystal Falls and other new-build areas, we’ve found initial cleaning at 18-24 months catches construction debris before it compacts. Call (737) 252-1285 and we’ll camera your system to give you a specific interval based on what we find.
Ready to see what’s inside your Abatement Technologies ductwork? Call (737) 252-1285 for a free estimate. We’ll put the camera in first, show you the photo, then talk about what comes next - with a written price before any work starts and a documented photo record when we leave.
Written by Tomas Reyes, Owner, CleanRun Air Duct Cleaning Leander at CleanRun Air Duct Cleaning Leander, serving Leander and nearby areas.